Pourable Concrete Filler - 25kg

Pourable Concrete Filler - 25kg

In Stock

The quickest and easiest way to fill holes on busy concrete floors, inside and out - with the lowest price guaranteed.

Perfect for durable, long lasting concrete repairs on heavily trafficked floors, floorsaver Pourable Concrete Filler is ready for foot traffic after only 1 hour, and heavy use after 4 hours. 

The lowest price - guaranteed!

Mix and pour - no primer required

Just add water and mix in the bucket provided

Ready to walk on after 1 hour



floorsaver Pourable Concrete Filler is best suited to holes in excess of 5mm thick. floorsaver Pourable Concrete Filler has been blended with polymers and accelerators. Just use as much as you need, mix with water, then pour straight into the hole - no wastage! Use in areas of heavy wear and tear such as factories, driveways, warehouses, car parks, etc.

Please note: we cannot accept returns for this product as they are cementitious.

You might also like: 


      How to Use

      Step 1 - Preparation:

      • Minimal preparation is required. floorsaver Pourable Concrete Filler is easy to use. Sweep out any loose stuff from the hole and that's about it.
      • If the repair will be heavily trafficked, (for instance forklifts) chip around the edge of the repair so that the Pourable Concrete Filler is a minimum of 3-5 mm thick around these areas. Scrape off any old paint (it doesn't matter if some well bonded paint remains) and cut out any concrete that has been contaminated with oil or fats. No need to prime. You can apply the filler to damp (not wet) surfaces.


      Step 2 - Mixing:

      • Remove the bag of powder from the bucket. The mix is 1 part water to 3 parts powder. Use a measuring jug or old cup to pour water into the bucket. You may want to start with a smaller mix until you get used to it.
      • You will need a mixing blade (we can supply one) fitted into an electric drill. Gradually add your powder. It's important to do it this way round, and until you get a pourable (slightly runny porridge) mix. If it's too stiff quickly add a drop more water, but if it's too runny add some more powder.
      • Only mix up what you can use within 10 minutes. Don't remix it once you have completed your initial mix (since the mixture will have started curing).


      Step 3 - Application:

      • Pour it into the hole. If you've got the mix right it will 'self-level' although you might have to spread it over large areas with a trowel.
      • Clean tools in water.

      Technical Spec

      Interior/exterior usage Suitable for interior and exterior use
      Coverage 10kg: Approx. 0.2m² at 25mm thick & 25kg: Approx. 0.5m²  at 25mm thick
      Finish Slip resistant finish
      Setting Time

      Drying time at a temperature of 10℃:

      • Initial Set - Dries quickly so only mix what you can use within 10 minutes
      • Foot traffic - 1 hour
      • Heavy traffic (vehicles and forklifts) - 4 hours
      Shelf Life Shelf Life - 12 months, if unopened and should not be allowed to freeze


      We don't recommend:

      • Using at temperatures below 5℃.
      • Using on slopes, step nosings, etc. since the product is pourable. For this type of repair use floorsaver Mouldable Concrete Filler or for surface imperfections (rather than 'big holes') use floorsaver Crack & Hole Filler.
      • Using at a depth of more than 100mm in one go. For very deep holes, allow a 100mm thick layer to dry for 12 hours , at a minimum temperature of 10℃, before applying the next.


      Product Information Sheet


      Safety Sheet



      Ask a Question
      • A: Yes you can paint over the Floor Saver Pourable Concrete Filler with either the Floor Saver Floor Paint or Epoxy Floor Paint. It will just need to be clean and dry.

      • A: Yes it is!

      • A: Hi, yes it can provided it's not applied in excessively hot temperatures (above 25°C) as this can lead to cracking.  If it is very hot, you could cover it (for around an hour) to protect it from the sun while it's drying. Also don't apply it in very cold conditions (below 5°C) or else it won't set.