Concrete Sealer Dustproofer - 25L

Concrete Sealer Dustproofer - 25L

In Stock

Seals, hardens and dustproofs weak porous concrete into a permanently strong floor. Unlike traditional dustproofers, floorsaver Concrete Sealer Dustproofer doesn’t leave a surface film which needs maintaining.

Doesn’t need recoating – does the job first time around

Easy to apply – just pour it on and sweep it around

Dries quickly and can be used inside or out

Lowest price guaranteed

Floorsaver Concrete Sealer Dustproofer is a penetrating dustproofer and hardener for concrete floors. This unique water based acrylic penetrates deeply into porous concrete leaving a dust free finish. Not only is it a highly effective dustproofer, but it strengthens the substrate too. Unlike traditional sealers and dustproofers, Floorsaver Concrete Sealer Dustproofer does not leave a surface film which needs maintaining, instead it does its job beneath the surface of the concrete. This high performance dustproofer binds weak, dusty concrete together, stabilising it and helping to prolong the life of the floor.

You don’t need to be an expert to apply Floorsaver Concrete Sealer Dustproofer as it’s incredibly easy. All you need to do is pour it on and sweep it around the area you want to seal. It dries quickly and helps to shrug off stains and dirt, making cleaning much easier. What’s more, you can use it both inside and out.

Please note: Concrete Sealer Dustproofer will be labelled as Concrete Dustproofer.

Step 1 - Preparation:

  • Surfaces should be clean and dry. If the floor is quite clean, a good sweep and vacuum may be enough.
  • Use Floorsaver Cleaner & Degreaser to remove oil and grease.
  • Floorsaver Concrete Sealer Dustproofer is suitable for bare, porous concrete only. If in doubt that your surface is porous, tip a cup of water onto it and see if some soaks in, if so, Floorsaver Sealer Dustproofer is suitable. If the water beads up on the floor and shows little sign of soaking in, please do not use our product.
  • Avoid washing very porous surfaces such as sand and cement screed since they will absorb too much water and you’ll need to wait approximately a day or so for them to dry out (depending on temperature).

Step 2 - Repairs:

  • Fill small surface holes and cracks using Floorsaver Crack & Hole Filler. Use Floorsaver Pourable Concrete Filler for holes 5mm50mm deep. Floorsaver Mouldable Concrete Filler can be used if you want a curved edge, such as a stair nosing, etc.
  • Just to be aware, you will see the repair through the clear dustproofer.

Step 3 - Application:

  • First of all make sure the area has good ventilation (i.e. doors and windows should be open to create a ‘through draught’) and that it’s warm enough for it to dry; you should aim for an air temperature of no less than 15°C.
  • Shake the container for a few seconds. Pour it onto the floor, a small area at a time, and distribute evenly using a soft broom, working it well into the surface. If it immediately ‘disappears’ into a very porous surface, add a little more. Keep the application even and avoid letting the product puddle on the surface. One is usually enough just to make sure all the ‘pores’ of the concrete have absorbed as much as they possibly can.
  • Clean applicators in water.
Content Water based acrylic
Interior/exterior usage Suitable for interior and exterior use
Surfaces Porous concrete
Drying times

Touch dry - 8 hours at 10℃, 4 hours at 20℃

Light traffic - 24 hours at 10℃, 12 hours at 20℃

Coverage

5L covers approximately 30m²

25L covers approximately 150m²

Shelf Life 12 months, if unopened and should not be allowed to freeze

 

We don't recommend:

  • Applying Concrete Sealer Dustproofer to very hard, dense non-porous surfaces such as power floated floors.
  • Applying Concrete Sealer Dustproofer to a previously painted or sealed surface.
  • Acid etching concrete before using Concrete Sealer Dustproofer.
  • Applying Concrete Sealer Dustproofer to a wet or damp surface - the floor must be dry.
  • Applying Concrete Sealer Dustproofer if the floor temperature is below 10°C.
  • Washing the floor for 24–48 hours after application (protect from rain during this time).

Product Information Sheet

Download

Safety Sheet

Download

QUESTIONS & ANSWERS

Ask a Question
  • A: The Concrete Dustproofer will be absolutely fine to use before applying an epoxy resin over the top.

    The Concrete Sealer is a colourless liquid resin which penetrates deep into concrete or other porous materials to provide a dustproofed, hardened surface.